工人舎 SH6KP10A に Debian lenny をインストール
こんなん買ったので何はともあれ Debian をインスコしてみた。
[rakuten:jism:10203968:detail]
バックアップ
Vista の初回起動前に、USB メモリに入れた Debian インストーラを使ってブートし、適当なところで「戻る」を選んでメニューの「シェルの起動」を選んで、
（適当な外付けドライブを /mnt にマウントして、） # dd if=/dev/hda bs=512 of=/mnt/sh6kp10a.hda.img
とやってハードディスクを丸ごとバックアップ。もちろんバックアップ先には空き領域が 100GB 以上必要。
インスコ
次に改めてインストーラをブートし、Vista からは D: に見える hda3 を削除、C: に見える hda2 を 72GB にリサイズし、空き領域に / と swap を作成。このとき、/ の起動フラグをオフり、Vista が入っている hda2 のフラグをオンにしておく。こうすると Vista の boot loader を使ってメニューが出る。以降の記事もそのつもりで書いているが，ここでフラグを / に付けたままにしておけば、起動時に GRUB を使うようになって、Vista には chainloader を使ってブートするようになる。
あとはいつものようにインストールし、「ハードディスクへの GRUB ブートローダのインストール」で、「マスターブートレコードに GRUB ブートローダをインストールしますか？」と聞かれたら、すかさず「いいえ」と答え、インストール先のデバイスに /dev/hda3 と入力する*1。
「再起動の準備ができた」と言ってきたら「戻る」を選び、「シェルの起動」を選んで、
# mount /hd-media -o rw,remount # インストーラのブートに使った USB メモリに書き込む # dd if=/dev/hda3 bs=512 count=1 of=/hd-media/grub.mbr # sync # mount /hd-media -o ro,remount
こうして作った grub.mbr を、Windows VistaとLinuxを共存させるには（Windows Vista編） − ＠IT の記事中の bcdedit のコマンドラインで使う。
あとは恐る恐るリブートしてみて、Vista の boot loader から GRUB が起動できるようになったことを確認する。
X が横に伸びている
SH6KP10A（以下 SH6）の解像度は 1024x600 だが、インストーラで入れたままの X だとこの解像度はサポートされず、かわりに 800x600 を引き伸ばして表示する。
/etc/X11/xorg.conf の Modes 行に "1024x600" を足すだけではだめで、
# aptitude install 915resolution
する必要があった。
Framebuffer Console
うちの /boot/grub/menu.lst の場合。
title Debian GNU/Linux, kernel 2.6.18-4-686 root (hd0,2) kernel /boot/vmlinuz-2.6.18-4-686 root=/dev/hda3 \ ro vga=789 video=intelfb:mode=1024x600-32 initrd /boot/initrd.img-2.6.18-4-686 savedefault
その他のデバイス
まだ試してない。
dmesg
Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12etch2) (dannf@debian.org) \
(gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) \
#1 SMP Wed May 9 23:03:12 UTC 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003f680000 (usable)
BIOS-e820: 000000003f680000 - 000000003f700000 (ACPI NVS)
BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
118MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7a50
On node 0 totalpages: 259712
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 30336 pages, LIFO batch:7
DMI present.
ACPI: RSDP (v002 PTLTD ) @ 0x000f79d0
ACPI: XSDT (v001 IECOEM KOHJINSH 0x06040000 LTP 0x00000000) @ 0x3f68211c
ACPI: FADT (v003 INTEL CALISTGA 0x06040000 ALAN 0x00000001) @ 0x3f687c06
ACPI: MADT (v001 INTEL CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f687cfa
ACPI: HPET (v001 INTEL CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f687d62
ACPI: MCFG (v001 INTEL CALISTGA 0x06040000 LOHR 0x0000005a) @ 0x3f687d9a
ACPI: TCPA (v001 PTLTD CALISTGA 0x06040000 PTL 0x00000001) @ 0x3f687dd6
ACPI: SLIC (v001 IECOEM KOHJINSH 0x06040000 PTL_ 0x00000000) @ 0x3f687e08
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3f687f7e
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x3f687fd8
ACPI: SSDT (v001 SataRe SataPri 0x00001000 INTL 0x20050624) @ 0x3f682e0b
ACPI: SSDT (v001 SataRe SataSec 0x00001000 INTL 0x20050624) @ 0x3f68276f
ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20050624) @ 0x3f682686
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20050624) @ 0x3f6821a0
ACPI: DSDT (v002 IECOEM KOHJINSH 0x06040000 INTL 0x20050624) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: 2 duplicate APIC table ignored.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:13 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 50000000 (gap: 40000000:bec00000)
Detected 600.047 MHz processor.
Built 1 zonelists. Total pages: 259712
Kernel command line: root=/dev/hda3 ro vga=789 video=intelfb:mode=1024x600-32
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1021072k/1038848k available (1544k kernel code, 16980k reserved, \
577k data, 196k init, 121344k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Calibrating delay using timer specific routine.. 1201.75 BogoMIPS (lpj=2403515)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000000 \
00000000 00000000
CPU: After vendor identify, caps: afe9fbff 00000000 00000000 00000000 00000000 \
00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 512K
CPU: After all inits, caps: afe9fbff 00000000 00000000 00000040 00000000 \
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) processor 600MHz stepping 08
Total of 1 processors activated (1201.75 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 5368k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 2.10 entry at 0xfd644, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#02) \
(try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 22) interrupt mode.
ACPI: Power Resource [FN00] (on)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x6a0-0x6af has been reserved
pnp: 00:07: ioport range 0x6b0-0x6ff has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:01.0
IO window: 2000-2fff
MEM window: f0100000-f01fffff
PREFETCH window: 52000000-520fffff
PCI: Bus 3, cardbus bridge: 0000:02:06.0
IO window: 00003000-000030ff
IO window: 00003400-000034ff
PREFETCH window: 50000000-51ffffff
MEM window: 54000000-55ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 3000-3fff
MEM window: f0200000-f02fffff
PREFETCH window: 50000000-51ffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 20 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:02:06.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1183591206.900:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
Allocate Port Service[0000:00:01.0:pcie02]
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3750k, total 7872k
vesafb: mode is 800x600x32, linelength=3200, pages=3
vesafb: protected mode interface info at 00ff:44f0
vesafb: scrolling: redraw
vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI: (supports S0<6>Time: tsc clocksource has been installed.
S3 S4 S5)
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Transitioning device [FAN0] to D0
ACPI: Transitioning device [FAN0] to D0
ACPI: Fan [FAN0] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, \
Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1
ACPI: Thermal Zone [TZ00] (63 C)
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
eth0: RTL8101e at 0xf882c000, 00:a0:d1:c2:5c:b3, IRQ 169
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 201, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 209, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 217
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 217, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 169, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xf0544000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 19 (level, low) -> IRQ 209
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
SCSI subsystem initialized
libata version 2.00 loaded.
Time: hpet clocksource has been installed.
hda: FUJITSU MHV2100AH PL, ATA DISK drive
usb 5-4: new high speed USB device using ehci_hcd and address 2
usb 5-4: configuration #1 chosen from 1 choice
usb 5-5: new high speed USB device using ehci_hcd and address 3
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ata_piix 0000:00:1f.2: version 2.00
ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ]
ata_piix 0000:00:1f.2: invalid MAP value 0
hda: max request size: 128KiB
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 <<6>ACPI: PCI Interrupt 0000:00:1f.2[B] -> \
GSI 19 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:00:1f.2 to 64
usb 5-5: configuration #1 chosen from 1 choice
ata1: SATA max UDMA/133 cmd 0x18D0 ctl 0x18C6 bmdma 0x18B0 irq 209
ata2: SATA max UDMA/133 cmd 0x18C8 ctl 0x18C2 bmdma 0x18B8 irq 209
scsi0 : ata_piix
hda5 >
ATA: abnormal status 0x7F on port 0x18D7
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0x18CF
usb 4-2: new full speed USB device using uhci_hcd and address 2
Attempting manual resume
usb 4-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: DIALOGUE INC PenMount USB as /class/input/input1
input: USB HID v0.01 Mouse [DIALOGUE INC PenMount USB] on usb-0000:00:1d.3-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xd0000000
intel_rng: FWH not detected
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1b.0 to 64
hda_codec: Unknown model for ALC262, trying auto-probe from BIOS...
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:02:06.3 [104c:803c] (rev 0)
ACPI: PCI Interrupt 0000:02:06.3[A] -> GSI 20 (level, low) -> IRQ 177
mmc0: SDHCI at 0xf0203000 irq 177 PIO
input: PC Speaker as /class/input/input2
Yenta: CardBus bridge found at 0000:02:06.0 [1170:0037]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:06.0, mfunc 0x00320422, devctl 0x66
Real Time Clock Driver v1.12ac
Yenta: ISA IRQ mask 0x0000, PCI irq 177
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
cs: IO port probe 0x3000-0x3fff: clean.
pcmcia: parent PCI bridge Memory window: 0xf0200000 - 0xf02fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 209
input: PS/2 Generic Mouse as /class/input/input3
ts: Compaq touchscreen protocol output
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x81a0b1, caps: 0xa04753/0x200000
input: SynPS/2 Synaptics TouchPad as /class/input/input4
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x407 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 1269092k swap on /dev/hda5. Priority:-1 extents:1 across:1269092k
EXT3 FS on hda3, internal journal
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; \
please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html \
for details.
r8169: eth0: link up
r8169: eth0: link up
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [ADP0] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
[drm] Initialized i915 1.5.0 20060119 on minor 0
